How to Remove Track Assembly for Caterpillar 320C Excavator

This instruction show you guide on how to remove track assembly for Caterpillar 320C excavator.

Procedures:
1. Install Tooling (D) in the track link and on the sprocket, as shown.
2. Start the machine. Move the sprocket forward until the track assembly is pulled up on the sprocket. Move the sprocket forward until the end of the track assembly is past a vertical line through the center of the sprocket. Remove Tooling (D).

3. Install Tooling (E) between the first bushing in the track link and the track shoe, as shown. 

CAT SIS 2021 EPC Service Manual Free Download
4. Move the sprocket forward. Use Tooling (E) to guide the track assembly over the carrier rollers and the front idler.

5. Use a suitable lifting device to raise the front of the track assembly. Install Tooling (A) in position under the track shoe, as shown.
6. Apply Tooling (F) on two track bushings. Install the bushings in the track links. The grease will hold the bushings in place.
7. Apply Tooling (F) in the master pin bores in the track assembly and on the master pin.
8. Connect the ends of the track assembly. Make sure that the pin bore in each end of the track assembly is aligned with each other.

9. Install Tooling (G) in the track assembly. Make sure that Tooling (G) is centered in the
track links. Use Tooling (G) and a hammer to install master pin (2).
Note: If you can not install master pin (2) with the hammer, use Tooling (C) to install
master pin (2). Refer to Illustration 5. 

CAT adapter 3
10. Install the cotter pin in the master pin. Remove Tooling (A) from the rear of the track assembly.
Note: Refer to Special Instruction, "Track - Assembly" for further information regarding
Tooling (C). 

CAT ET 2022A Diagnostic Software
11. If the track shoe on each side of the master pin was removed, reinstall the track shoes. Use Tooling (B) to reinstall the track shoe mounting bolts.
12. Tighten the tension of the track. Refer to Operation and Maintenance Manual, "Track Adjustment - Adjust" for the correct procedure.

Source:https://caterpillar-macine-repair.blogspot.com/2022/07/how-to-remove-track-assembly-for.html

Comments

Post a Comment

Popular posts from this blog

Caterpillar Compression Brake Solenoid Test Guide

Caterpillar Compression Brake Solenoid Test function allows brake wiring or solenoid problems to be identified when the engine is not running. This test does not verify proper brake valve actuation.   Related Contents: Caterpillar ET 2023C 2019C 2018A Electronic Technician Software Free Download CAT Adapter 3 ET4 478-0235 High Quality Diagnostic Adapter Caterpillar SIS 2021 2019 2018 Full EPC+Service Manual Free Download Caterpillar 18 digits factory password calculator Accessing To run the Compression Brake Solenoid Test function: Select “Diagnostic Tests” from the Diagnostics menu, and then select “Compression Brake Solenoid Test” from the submenu. The Compression Brake Solenoid Test screen is displayed. Screen Layout The Compression Brake Solenoid Test screen has the following areas: Tree Area The Injector Solenoid Test Tree area lists the available ECMs and the selected diagnostic test. Note: If more than one diagnostic test is available, the selected test will be highlighted. ...
Read more

How to Build Connection between PC and CAT ET4 Adapter

Image
Here is a guide on how to build connection between laptop and CAT ET4 diagnostic adapter . To connect the Communication Adapter 3 (“Comm Adapter 3”) to the PC, perform the following steps: Step 1: Align and attach the DB25 connector end of the USB PC cable to the “PC cable” end connection on the Comm Adapter 3. Step 2: Plug the USB Connector end of the PC cable into the USB port of the PC To connect the Comm Adapter 3 to the data link, perform the following steps: Step 1 After connecting the Comm Adapter 3 to the PC, connect the DB15-style connector end of the data link cable to the “Data Link” connection on the Comm Adapter 3. Step 2 Connect the other end of the data link cable to the service connector on the product. The lights on the front of the Comm Adapter 3 will glow and then will sequentially turn off from the top (“Data Link” end) to the bottom (“Computer” end) of the device. The Power LED will turn color from orange to red, and then the blue "USB" LED will blink onc...
Read more

How to Change Cooling System Coolant (DEAC) for Caterpillar 950F

This instruction show  you guide on how to  change cooling system coolant (DEAC) for Caterpillar 950F.More about Caterpillar repair manuals please refer to: CAT SIS 2021   Pressurized system: Hot coolant can cause serious burn. To open cap, stop engine, wait until radiator is cool. Then loosen cap slowly to relieve the pressure. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing,adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Note: This procedure pertains to Caterpillar Diesel Engine Antifreeze/Coolant (DEAC) only. This procedure does not pertain to machi...
Read more