Caterpillar C11 & C13 Industrial Engine Start and Stopping Notice

 Here are some notice options before you starting Caterpilar C11 and C13 industrical engine.All about Caterpillar machine,please refer to:Caterpillar SIS EPC+Service

Inspect the engine for potential hazards.
Before starting the engine, ensure that no one is on,underneath, or close to the engine. All protective guards and all protective covers must be installed if the engine must be started in order to perform service procedures. To help prevent an accident that is caused by parts in rotation, work around the parts carefully.
Do not bypass the automatic shutoff circuits. Do not disable the automatic shutoff circuits. The circuits are provided in order to help prevent personal injury. The circuits are also provided in order to help prevent engine damage.
On the initial start-up of a new engine or an engine that has been serviced, prepare to stop the engine if an overspeed condition occurs. This may be accomplished by shutting off the fuel supply to the engine and/or shutting off the air supply to the engine.
See the Service Manual for repairs and for adjustments.

 Caterpillar CAT ET diagnostic software

Engine Starting
If a warning tag is attached to the engine start switch or to the controls, DO NOT start the engine or move the controls. Consult with the person that attached the warning tag before the engine is started.
All protective guards and all protective covers must be installed if the engine must be started in order to perform service procedures. To help prevent an accident that is caused by parts in rotation, work around the parts carefully.
Start the engine from the operator’s compartment or from the engine start switch.
Always start the engine according to the procedure that is described in the Operation and Maintenance Manual, “Engine Starting” topic in the Operation Section. Knowing the correct procedure will help to prevent major damage to the engine components.
Knowing the procedure will also help to prevent personal injury.
To ensure that the jacket water heater (if equipped) and/or the lube oil heater (if equipped) is working properly, check the water temperature and the oil temperature during heater operation.
Engine exhaust contains products of combustion which can be harmful to your health. Always start the engine and operate the engine in a well ventilated area. If the engine is started in an enclosed area,vent the engine exhaust to the outside
 

Engine Stopping
Stop the engine according to the procedure in the Operation and Maintenance Manual, “Engine Stopping (Operation Section)” in order to avoid overheating of the engine and accelerated wear of the engine components.
Use the Emergency Stop Button (if equipped) ONLY in an emergency situation. Do not use the Emergency Stop Button for normal engine stopping. After an emergency stop, DO NOT start the engine until the problem that caused the emergency stop has been
corrected. 

Caterpillar SIS 2020 2019 Full EPC+Service Manual Free Download

Stop the engine if an overspeed condition occurs during the initial start-up of a new engine or an engine that has been overhauled. This may be accomplished by shutting off the fuel supply to the engine and/or shutting off the air supply to the engine.
To stop an electronically controlled engine, cut the power to the engine.

Electrical System
Never disconnect any charging unit circuit or battery circuit cable from the battery when the charging unit is operating. A spark can cause the combustible
gases that are produced by some batteries to ignite.
To help prevent sparks from igniting combustible gases that are produced by some batteries, the negative “-” jump start cable should be connected last from the external power source to the negative“-” terminal of the starting motor. If the starting motor is not equipped with a negative “-” terminal, connect the jump start cable to the engine block.
Check the electrical wires daily for wires that are loose or frayed. Tighten all loose electrical wires before the engine is started. Repair all frayed electrical wires before the engine is started. See the Operation and Maintenance Manual for specific starting instructions.
http://www.car-auto-repair.com/caterpillar-sis-2018-full-free-download/

Comments

Post a Comment

Popular posts from this blog

Caterpillar Compression Brake Solenoid Test Guide

Caterpillar Compression Brake Solenoid Test function allows brake wiring or solenoid problems to be identified when the engine is not running. This test does not verify proper brake valve actuation.   Related Contents: Caterpillar ET 2023C 2019C 2018A Electronic Technician Software Free Download CAT Adapter 3 ET4 478-0235 High Quality Diagnostic Adapter Caterpillar SIS 2021 2019 2018 Full EPC+Service Manual Free Download Caterpillar 18 digits factory password calculator Accessing To run the Compression Brake Solenoid Test function: Select “Diagnostic Tests” from the Diagnostics menu, and then select “Compression Brake Solenoid Test” from the submenu. The Compression Brake Solenoid Test screen is displayed. Screen Layout The Compression Brake Solenoid Test screen has the following areas: Tree Area The Injector Solenoid Test Tree area lists the available ECMs and the selected diagnostic test. Note: If more than one diagnostic test is available, the selected test will be highlighted. ...
Read more

How to Build Connection between PC and CAT ET4 Adapter

Image
Here is a guide on how to build connection between laptop and CAT ET4 diagnostic adapter . To connect the Communication Adapter 3 (“Comm Adapter 3”) to the PC, perform the following steps: Step 1: Align and attach the DB25 connector end of the USB PC cable to the “PC cable” end connection on the Comm Adapter 3. Step 2: Plug the USB Connector end of the PC cable into the USB port of the PC To connect the Comm Adapter 3 to the data link, perform the following steps: Step 1 After connecting the Comm Adapter 3 to the PC, connect the DB15-style connector end of the data link cable to the “Data Link” connection on the Comm Adapter 3. Step 2 Connect the other end of the data link cable to the service connector on the product. The lights on the front of the Comm Adapter 3 will glow and then will sequentially turn off from the top (“Data Link” end) to the bottom (“Computer” end) of the device. The Power LED will turn color from orange to red, and then the blue "USB" LED will blink onc...
Read more

How to Change Cooling System Coolant (DEAC) for Caterpillar 950F

This instruction show  you guide on how to  change cooling system coolant (DEAC) for Caterpillar 950F.More about Caterpillar repair manuals please refer to: CAT SIS 2021   Pressurized system: Hot coolant can cause serious burn. To open cap, stop engine, wait until radiator is cool. Then loosen cap slowly to relieve the pressure. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing,adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, “Caterpillar Tools and Shop Products Guide” for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Note: This procedure pertains to Caterpillar Diesel Engine Antifreeze/Coolant (DEAC) only. This procedure does not pertain to machi...
Read more